Wago Adapter - Revision history

Jasx at 20:54, 26 March 2026

2026-03-26T20:54:43Z

← Older revision		Revision as of 20:54, 26 March 2026
Line 23:		Line 23:
	[[File:Step02.jpg\|frameless]]		[[File:Step02.jpg\|frameless]]

	'''Step 3:''' Press down on the "button" on top and slide the cable in. If you give it a gentle tug after and it doesn't release, you're good!		'''Step 3:''' Press down on the "button" on top and slide the cable in. If you give it a gentle tug after, and it doesn't release, you're good!
	''Note: The polarity of the wires doesn't matter, you can attach them in any order!''		''Note: The polarity of the wires doesn't matter, you can attach them in any order!''

Line 30:		Line 30:

	'''Step 4:''' Repeat with the other wire.		'''Step 4:''' Repeat with the other wire.



	[[File:Step04.jpg\|frameless]]		[[File:Step04.jpg\|frameless]]

	'''Step 5:''' Do the same with the other vibrator if you wish, but that's it! '''You're done!'''		'''Step 5:''' Do the same with the other vibrator if you wish, but that's it! '''You're done!'''

Jasx at 20:54, 26 March 2026

2026-03-26T20:54:01Z

← Older revision		Revision as of 20:54, 26 March 2026
Line 14:		Line 14:

	'''Step 1:''' Cut the cord. You want a lead connected directly to the vibrator!		'''Step 1:''' Cut the cord. You want a lead connected directly to the vibrator!


	[[File:Step01.jpg\|frameless]]		[[File:Step01.jpg\|frameless]]

	'''Step 2:''' Split and strip a bit at the end of the cord to expose some copper. 5mm (0.2") is enough.		'''Step 2:''' Split and strip a bit at the end of the cord to expose some copper. 5mm (0.2") is enough.


	[[File:Step02.jpg\|frameless]]		[[File:Step02.jpg\|frameless]]

	'''Step 3:''' Press down on the "button" on top and slide the cable in. If you give it a gentle tug after and it doesn't release, you're good!		'''Step 3:''' Press down on the "button" on top and slide the cable in. If you give it a gentle tug after and it doesn't release, you're good!
	''Note: The polarity of the wires doesn't matter, you can attach them in any order!''		''Note: The polarity of the wires doesn't matter, you can attach them in any order!''


	[[File:Step03.jpg\|frameless]]		[[File:Step03.jpg\|frameless]]

Jasx: Created page with "The Wago Adapter is a cheap way to turn most dumb 5V vibrators into smart ones. The VibHub Wago adapter is a little bare circuit adapter that lets you convert most dumb 5V vibrators into smart ones by cutting and stripping the cable. === Basic Use === First off you need a vibrator that's capable. Check the Compatible Toys page for more info! In this tutorial, we'll be using a common 2-in-one vibrator from AliExpress...."

2026-03-26T20:53:30Z

Created page with "thumb|The Wago Adapter is a cheap way to turn most dumb 5V vibrators into smart ones. The VibHub Wago adapter is a little bare circuit adapter that lets you convert most dumb 5V vibrators into smart ones by cutting and stripping the cable. === Basic Use === First off you need a vibrator that's capable. Check the Compatible Toys page for more info! In this tutorial, we'll be using a common 2-in-one vibrator from AliExpress...."

New page

[[File:Wago adapter.jpg|thumb|The Wago Adapter is a cheap way to turn most dumb 5V vibrators into smart ones.]]
The VibHub Wago adapter is a little bare circuit adapter that lets you convert most dumb 5V vibrators into smart ones by cutting and stripping the cable.

=== Basic Use ===
First off you need a vibrator that's capable. Check the [[Compatible toys|Compatible Toys]] page for more info!

In this tutorial, we'll be using a common 2-in-one vibrator from AliExpress. At the time of writing, these sell for like $4 per pair, so they're almost cheap enough to be considered disposable. A cheap egg vibrator is a good starting point in case you don't know what you're doing. But connecting a simple wire-remote device to a VibHub is very easy.

''Before you begin, '''please note that the process is destructive''', as you'll be cutting the cord! Don't convert a vibrator if you want to restore it at a later date!''

Also note that you can do one vibrator per adapter, don't cram multiple cords in there!
[[File:ExampleProduct.jpg|thumb|Example of a cheap vibrator that can be used.]]
[[File:Step00.jpg|frameless]]

'''Step 1:''' Cut the cord. You want a lead connected directly to the vibrator!
[[File:Step01.jpg|frameless]]
'''Step 2:''' Split and strip a bit at the end of the cord to expose some copper. 5mm (0.2") is enough.
[[File:Step02.jpg|frameless]]
'''Step 3:''' Press down on the "button" on top and slide the cable in. If you give it a gentle tug after and it doesn't release, you're good!
''Note: The polarity of the wires doesn't matter, you can attach them in any order!''
[[File:Step03.jpg|frameless]]

'''Step 4:''' Repeat with the other wire.

[[File:Step04.jpg|frameless]]

'''Step 5:''' Do the same with the other vibrator if you wish, but that's it! '''You're done!'''